景區公園廣場游樂設備出現故障應該怎么辦
作者：龍之盈游樂
發布日期：2022-09-09
閱讀次數：73
景區公園廣場游樂設備出現故障應該怎么辦
游樂設備運行過程中總是會發生故障，那么游樂設備發生故障應該怎么處理？
一、無法起動
1，電控柜及線路故障。
無法開機檢查電控柜工作狀態，看電控柜電源指示燈是否點亮，當指示燈點亮時表示電源接電控柜線沒有問題，指示燈點亮時檢查電源接電控柜線是否斷線、短路，如果有的話再接或者換線。沒有問題就繼續開電控柜，查看繼電器閘刀是否合閘、保險是否熔斷，如果是就合閘、換閘。檢查繼電器線圈內部有否損壞或者保險絲斷了的問題，若沒有及時更換就會出現不正常的工作狀態。檢查轉馬(ma)內有無磨損、松動等問題。如故障依舊，請檢查電控柜接轉馬(ma)導電環是否斷開（轉馬(ma)導電環所在部位為轉馬(ma)中柱），轉馬(ma)導電環與電機之間是否斷開，如斷開再接或者換線。檢查導電環與碳刷接觸點是否有灰塵、接觸不良等現象，如有能用螺絲刀壓幾次。
2、電機故障。
電控柜及線路均無故障或故障排除后仍不能起動應檢查是否為電機故障，將電機皮帶輪處皮帶拆除，電控柜開始打開開機按鈕，再觀察電機是否正常運轉，如不正常即為電機損壞，需更換電機。
二、起動困難
1、軸承太緊了。主要原因是：①安裝不當；②潤滑不良；③使用中磨損或損壞等。解決方法為更換新件和重新緊固螺釘。2.齒輪間隙過大。主要原因有兩個。發生這類故障通常以新轉馬為主，可以用扳手調節，松緊度適中就可以了，此外還可以加潤滑油更有效。
2、電壓不穩，太低。許多設備起動困難或者起動不起來就是因為電壓不穩或者太低，多由附近電壓負載太大引起，這種情況在夏天就非常明顯了。檢查方法為：按動電控柜上的啟動按鈕觀察電壓表工作情況。解決之道在于替換更大平方厘米數量的電源線，或者替換線路接入點。如果發現問題要馬上排除，不要延誤了營業時間。
